DFI UT P35-T2R: Tweakers Rejoice!
- Posted in
- Motherboards
BIOS TRD Phase Adjust
465FSB BIOS Settings
For our 465 FSB Prime stable test, we used the 333/800 strap. We set Performance Level 7, targeted a 465FSB x 8 CPU speed, and ran 4GB of OCZ Flex 9200. The remaining BIOS DRAM Settings were as follows:
Even though we have set Performance Level 7 in the DRAM page, this particular TRD Phase sequence is virtually running a Performance Level of 6 throughout the entire TRD cycle with the exception of a single TRD phase set to 7 (Channel 2 Phase 1) to create the breathing space necessary for the Northbridge to hold steady at 465FSB with 4GB of RAM. When setting a series of phases to ENABLED on both channels, Channel 2 will require an offset as can be seen in the list of settings we used above. If Channel 1 Phase 0, Phase 1 and Channel 2 Phase 0 are set to ENABLED, Channel 2 Phase 1 must be set to AUTO.
Running two or more corresponding phases at ENABLED on both channels is more aggressive, as it sets the corresponding TRD phase registers to -1 at the same point of the TRD cycle, resulting in a lower latency and thus a higher load on the chipset. The general advantage of TRD phase adjustments is to increase FSB margins while retaining significant amounts of latency and bandwidth at FSBs that fall between the borders of two Performance Levels.
Setting a single channel's phase to ENABLED while the corresponding phase for the other channel is set to AUTO results in a very slight gain in latency and bandwidth, which can be useful for maximizing overall performance.
The above timing and phase combinations are only applicable for the setting of 465FSB using the 333/800 divider and Performance Level 7. Scaling the FSB higher will require further tuning and perhaps returning some of the phases back to AUTO. We must consider that various memory settings can affect the level of TRD adjustments that can be made. Experimentation will be required by the user when changing CPU/RAM MHz (FSB) and also primary/secondary RAM timings.
465FSB BIOS Settings
For our 465 FSB Prime stable test, we used the 333/800 strap. We set Performance Level 7, targeted a 465FSB x 8 CPU speed, and ran 4GB of OCZ Flex 9200. The remaining BIOS DRAM Settings were as follows:
| 465FSB BIOS Settings | |
| CPU Feature | |
| Thermal Management Control | Disabled |
| PPM (EIST) Mode | Disabled |
| Limit CPUID MaxVal | Disabled |
| CIE Function | Disabled |
| Execute Disable Bit | Enabled |
| Virtualization Technology | Enabled |
| Core Multi-Processing | Enabled |
| Exist Setup Shutdown | Mode 2 |
| CLOCK VC0 divider | AUTO |
| CPU Clock Ratio | 8x |
| Target CPU Clock | 3722MHz |
| CPU Clock | 465FSB |
| Boot Up Clock | AUTO |
| DRAM Speed | 333MHz/800MHz |
| Target DRAM Speed | DDR2-1116MHz |
| PCIE Clock | 100MHz |
| Voltage Settings | |
| CPU VID Control | 1.4375 |
| CPU VID Special Add | AUTO |
| DRAM Voltage Control | 2.12 |
| SB 1.05V Voltage | 1.07v |
| SB Core/CPU PLL Voltage | 1.55v |
| NB Core Voltage | 1.65 |
| CPU VTT Voltage | 1.60v |
| VCore Droop Control | Disabled |
| Clockgen Voltage Control | 3.45v |
| GTL+ Buffers Strength | Strong |
| Host Slew Rate | Weak |
| GTL REF Voltage Control | Enabled |
| x CPU GTL1/3 REF Volt | 115 |
| x CPU GTL 0/2 REF Volt | 115 |
| x North Bridge GTL REF Volt | 117 |
| DRAM Timing | |
| Enhance Data transmitting | FAST |
| Enhance Addressing | FAST |
| T2 Dispatch | Disabled |
| Channel 1 CLK Crossing Setting | More Aggressive |
| Channel 2 CLK Crossing Setting | More Aggressive |
| CH1CH2 Common CLK Crossing Setting | More Aggressive |
| CAS Latency Time (tCL) | 5 |
| RAS# to CAS# Delay (tRCD) | 5 |
| RAS# Precharge (tRP) | 4 |
| Precharge Delay (tRAS) | 9 |
| All Precharge to Act | 4 |
| REF to ACT Delay (tRFC) | 30 |
| Performance Level | 7 |
| Read delay phase adjust | SEE BELOW |
| MCH ODT Latency | 1 |
| Write to PRE Delay (tWR) | 12 |
| Rank Write to Read (tWTR) | 10 |
| ACT to ACT Delay (tRRD) | 3 |
| Read to Write Delay (tRDWR) | 8 |
| Ranks Write to Write (tWRWR) | AUTO |
| Ranks Read to Read (tRDRD) | AUTO |
| Ranks Write to Read (tWRRD) | AUTO |
| Read CAS# Precharge (tRTP) | 3 |
| ALL PRE to Refresh | 4 |
| PCIE Slot Config | 1X 1X |
| CPU Spread Spectrum | Disabled |
| PCIE Spread Spectrum | Disabled |
| SATA Spread Spectrum | Disabled |
| TRD Phase adjust settings | |
| Channel 1 Phase 0 Pull-In | ENABLED (TRD 6) |
| Channel 1 Phase 1 Pull-In | ENABLED (TRD 6) |
| Channel 1 Phase 2 Pull-In | ENABLED (TRD 6) |
| Channel 1 Phase 3 Pull-In | ENABLED (TRD 6) |
| Channel 1 Phase 4 Pull-In | ENABLED (TRD 6) |
| Channel 2 Phase 0 Pull-In | ENABLED (TRD 6) |
| Channel 2 Phase 1 Pull-In | AUTO (TRD 7) |
| Channel 2 Phase 2 Pull-In | ENABLED (TRD 6) |
| Channel 2 Phase 3 Pull-In | ENABLED (TRD 6) |
| Channel 2 Phase 4 Pull-In | ENABLED (TRD 6) |
Even though we have set Performance Level 7 in the DRAM page, this particular TRD Phase sequence is virtually running a Performance Level of 6 throughout the entire TRD cycle with the exception of a single TRD phase set to 7 (Channel 2 Phase 1) to create the breathing space necessary for the Northbridge to hold steady at 465FSB with 4GB of RAM. When setting a series of phases to ENABLED on both channels, Channel 2 will require an offset as can be seen in the list of settings we used above. If Channel 1 Phase 0, Phase 1 and Channel 2 Phase 0 are set to ENABLED, Channel 2 Phase 1 must be set to AUTO.
Running two or more corresponding phases at ENABLED on both channels is more aggressive, as it sets the corresponding TRD phase registers to -1 at the same point of the TRD cycle, resulting in a lower latency and thus a higher load on the chipset. The general advantage of TRD phase adjustments is to increase FSB margins while retaining significant amounts of latency and bandwidth at FSBs that fall between the borders of two Performance Levels.
Setting a single channel's phase to ENABLED while the corresponding phase for the other channel is set to AUTO results in a very slight gain in latency and bandwidth, which can be useful for maximizing overall performance.
The above timing and phase combinations are only applicable for the setting of 465FSB using the 333/800 divider and Performance Level 7. Scaling the FSB higher will require further tuning and perhaps returning some of the phases back to AUTO. We must consider that various memory settings can affect the level of TRD adjustments that can be made. Experimentation will be required by the user when changing CPU/RAM MHz (FSB) and also primary/secondary RAM timings.
Originally published at https://www.anandtech.com/show/2354 (Wayback Machine).