DFI UT P35-T2R: Tweakers Rejoice!
- Posted in
- Motherboards
All Other Sub-Timings-

Using AUTO for all sub-timings is generally acceptable until we start pushing for every last MHz of bandwidth and latency. The BIOS defaults are generally tight enough for very good performance on 24/7 PCs. The BIOS profiles we are including in this article have been tuned for maximum performance while retaining full system stability. We used Memset 3.3 while running Microsoft XP to check where the AUTO DRAM timing defaults set the memory parameters. The timings shown by Memset were noted by us and entered manually into the relevant BIOS functions. We then began to tighten these values one at a time, noting the effects of any changes on bandwidth, latency, and stability.
For benchmarking we tend to use Memset once the XP operating system has loaded rather than entering overly tight settings directly in the BIOS. We can then begin to tighten the sub-timings far beyond 24/7 settings. We have attached Memset screenshots for both our 24/7 stable and sub-zero benchmarking so that users can see how far we were able to push for maximum scores.
Additional Setting Ranges:
MCH ODT Latency: ODT (On Die Termination) is used to match the MCH output impedance to the termination resistance of the RAM. Use of 1-2 is fine in most cases. Even for 4GB overclocking we did not find that more than a setting of 1 was required.
Write to PRE Delay (tWR): Range is from 10-13. For high RAM speed, use 12 and above for stability; for benchmarking 10-12 will be faster. Lower is faster.
Rank Write to Read (tWTR): Range is 9-11. Use 11 for stability and 10 or 9 for benchmarking. Lower is faster.
ACT to ACT Delay (tRRD): Range is 2-5. 3 is a good setting that allows high enough FSBs for most users. Higher numbers result in less memory read performance.
Read to Write Delay (tRDWR): Range is 8-9. 8 is ideal for most users; higher values are slower.
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
The ranges for all these settings are quite well manipulated by SPD and BIOS. For those wishing to experiment, 4 is the lowest and most aggressive setting. 5-4-5 may work for SuperPi type benching. There is a slight write/copy speed increase with tighter settings, but this is only useful for the extracting the last ounce of performance. For stability these are best left on AUTO
Read CAS# Precharge (tRTP): 2-3 works well on this board for most users. 2 is used for benchmarking while 3 and upwards are best for stability.
ALL PRE to Refresh: Range is 4-5. 4 works fine with quad-core CPUs all the way to 475 FSB. A setting of 4 is fine for most benchmarking, unless shooting high over 500FSB.

Using AUTO for all sub-timings is generally acceptable until we start pushing for every last MHz of bandwidth and latency. The BIOS defaults are generally tight enough for very good performance on 24/7 PCs. The BIOS profiles we are including in this article have been tuned for maximum performance while retaining full system stability. We used Memset 3.3 while running Microsoft XP to check where the AUTO DRAM timing defaults set the memory parameters. The timings shown by Memset were noted by us and entered manually into the relevant BIOS functions. We then began to tighten these values one at a time, noting the effects of any changes on bandwidth, latency, and stability.
For benchmarking we tend to use Memset once the XP operating system has loaded rather than entering overly tight settings directly in the BIOS. We can then begin to tighten the sub-timings far beyond 24/7 settings. We have attached Memset screenshots for both our 24/7 stable and sub-zero benchmarking so that users can see how far we were able to push for maximum scores.
Additional Setting Ranges:
MCH ODT Latency: ODT (On Die Termination) is used to match the MCH output impedance to the termination resistance of the RAM. Use of 1-2 is fine in most cases. Even for 4GB overclocking we did not find that more than a setting of 1 was required.
Write to PRE Delay (tWR): Range is from 10-13. For high RAM speed, use 12 and above for stability; for benchmarking 10-12 will be faster. Lower is faster.
Rank Write to Read (tWTR): Range is 9-11. Use 11 for stability and 10 or 9 for benchmarking. Lower is faster.
ACT to ACT Delay (tRRD): Range is 2-5. 3 is a good setting that allows high enough FSBs for most users. Higher numbers result in less memory read performance.
Read to Write Delay (tRDWR): Range is 8-9. 8 is ideal for most users; higher values are slower.
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
The ranges for all these settings are quite well manipulated by SPD and BIOS. For those wishing to experiment, 4 is the lowest and most aggressive setting. 5-4-5 may work for SuperPi type benching. There is a slight write/copy speed increase with tighter settings, but this is only useful for the extracting the last ounce of performance. For stability these are best left on AUTO
Read CAS# Precharge (tRTP): 2-3 works well on this board for most users. 2 is used for benchmarking while 3 and upwards are best for stability.
ALL PRE to Refresh: Range is 4-5. 4 works fine with quad-core CPUs all the way to 475 FSB. A setting of 4 is fine for most benchmarking, unless shooting high over 500FSB.
Originally published at https://www.anandtech.com/show/2354 (Wayback Machine).