Swiftech H2O-120 Compact and Corsair Nautilus 500: Is Water Better?
- Posted in
- Cases/Cooling/PSUs
Swiftech H2O-120 Compact Specifications
Our test system is Intel Socket 775, but the H2O-120 Compact will also mount on socket AM2 as well as socket 754/939/940 and socket F. All accessories for mounting are included, but mounting on AMD/AM2 sockets requires adapting the Apogee drive block by replacing the bottom half of the Apogee with an AMD specific mounting block. The CPU cage is then removed from the motherboard for the two or four screw direct mount of the drive block

The included fan is specified at a high 81.3 CFM at 12V, but it is rated at a bit higher noise than we normally see at this output. The 12V rated noise is 36 dB(A). Lowering the fan voltage to 7V with the included electrical adapter drops the noise to 26 dB(A) with the trade-off of much lower airflow. Sleeve bearings are not noted for a long service life, but Swiftech does not specify an average MTBF for this fan.
The Reservoir/Heat Exchanger utilizes louvered copper fins for best performance. Swiftech claims the system is optimized for high performance at low fan speed where low noise is required.
The Apogee Drive Block is extremely small compared to the size and weight of most of today's better air coolers. This makes the Apogee drive block an easy fit on virtually any motherboard. The only potential issue is the side-mounted 3/8" barbs on the combo block. On some motherboards with tall heatsinks for the power MOSFETs the barbs are potentially not tall enough to clear the tall MOSFET sinks However, we did not encounter this issue with any of the boards we looked at for potential mounting problems.
There are no mounting issues with the EVGA 680i board. Installation was also an easy task on the ASUS Striker and ASUS Commando, and on the two new P35 boards - the ASUS P5K Deluxe and P5K3 Deluxe. The P5K3 Deluxe will likely become a fit test for any motherboard, since the heatpipes completely circle the CPU socket and connect various cooling heatsinks around the CPU socket.
Corsair Nautilus 500 Specifications
The Nautilus 500 was tested on Intel Socket 775. The kit also includes retention brackets for Intel socket 478 and AMD 754/939/940/AM2 sockets. The vinyl tubing for the circulating water is attached to the water block at the factory. The water block remains the same in all possible installations and only the retention mechanism for mounting varies among the different installations. This is an important consideration since this approach ensures that the critical internal water connection is assembled at the factory and already tested for leaks.
The supporting components and self-contained design makes some small differences in the pump specifications between the Corsair and Swiftech designs. Corsair has also selected a different fan to be integrated in the external cooler. The 1800 RPM Nautilus 500 fan has a maximum air flow of 74.4 CFM, which is slightly less than the 81.3 CFM of the Swiftech. However, static pressure is higher on the Corsair fan.
The CPU clock looks very similar to the water block used in the Swiftech H2O-120 Compact. The Corsair design uses a stand-alone water block and does not integrate the block and pump as we saw in the Swiftech. This moves the pump noise from inside the case, as in the Swiftech, to outside the case in the cooling box on the Corsair. Which is the better design is a matter for debate, but as you'll see shortly we consider both designs noisier than the best air cooler designs.
There was no problem with fitting the Nautilus 500 waterblock to any motherboard we tested, and in fact we doubt you can find a motherboard that cannot mount the Corsair water block. Since the water block is standalone in the Corsair design there is no potential issue with side barbs as we saw on the Swiftech
Our test system is Intel Socket 775, but the H2O-120 Compact will also mount on socket AM2 as well as socket 754/939/940 and socket F. All accessories for mounting are included, but mounting on AMD/AM2 sockets requires adapting the Apogee drive block by replacing the bottom half of the Apogee with an AMD specific mounting block. The CPU cage is then removed from the motherboard for the two or four screw direct mount of the drive block

| Apogee Drive Block Specifications | |
| Motor | Electronically commutated, brushless 12V DC, spherical motor |
| Nominal Current | 0.69A |
| Weight | 286g (10.1 ounces) |
| Material | Diamond Pin Matrix copper base plate |
| Fittings | 3/8" barbs fittings for input and output |
| Normal Discharge | 300 LPH |
| Nominal Head | 10 ft |
| MTBF | 50,000 hours |
The included fan is specified at a high 81.3 CFM at 12V, but it is rated at a bit higher noise than we normally see at this output. The 12V rated noise is 36 dB(A). Lowering the fan voltage to 7V with the included electrical adapter drops the noise to 26 dB(A) with the trade-off of much lower airflow. Sleeve bearings are not noted for a long service life, but Swiftech does not specify an average MTBF for this fan.
| 120mm Fan Specifications | |
| Model | RDM1225S |
| Fan Size | 120mm x 120mm x 25mm |
| Fan Type | Low Noise Sleeve Bearing |
| Maximum Fan Speed | 2000 RPM |
| Maximum Noise Level | 36 dB(A) @ 12V, 26 dB(A) @ 7V |
| Maximum Airflow | 81.3 CFM |
| Current | 0.23A |
| Static Pressure | 27mm H2O |
The Reservoir/Heat Exchanger utilizes louvered copper fins for best performance. Swiftech claims the system is optimized for high performance at low fan speed where low noise is required.
| Radiator/Reservoir Specification | |
| Model | MCR120-Res Heat Exchanger |
| Description | 120mm Class Radiator with built-in reservoir. Designed for sealed system with 5 years between refilling |
| Dimensions | 7in x 5in x 1-3/8in (2" thick including barbs) |
| Material | Louvered copper fins, brass tubes & body |
| Design | Optimized for high performance at low fan speed for low noise operations |
| Fittings | Built-in 3/8 in barbs |
The Apogee Drive Block is extremely small compared to the size and weight of most of today's better air coolers. This makes the Apogee drive block an easy fit on virtually any motherboard. The only potential issue is the side-mounted 3/8" barbs on the combo block. On some motherboards with tall heatsinks for the power MOSFETs the barbs are potentially not tall enough to clear the tall MOSFET sinks However, we did not encounter this issue with any of the boards we looked at for potential mounting problems.
There are no mounting issues with the EVGA 680i board. Installation was also an easy task on the ASUS Striker and ASUS Commando, and on the two new P35 boards - the ASUS P5K Deluxe and P5K3 Deluxe. The P5K3 Deluxe will likely become a fit test for any motherboard, since the heatpipes completely circle the CPU socket and connect various cooling heatsinks around the CPU socket.
Corsair Nautilus 500 Specifications
The Nautilus 500 was tested on Intel Socket 775. The kit also includes retention brackets for Intel socket 478 and AMD 754/939/940/AM2 sockets. The vinyl tubing for the circulating water is attached to the water block at the factory. The water block remains the same in all possible installations and only the retention mechanism for mounting varies among the different installations. This is an important consideration since this approach ensures that the critical internal water connection is assembled at the factory and already tested for leaks.
| Water Pump | |
| Motor | Electronically commutated, brushless 12V DC, spherical Motor |
| Voltage Range | 8V to 13.2V |
| Max Static Pressure | 22 PSI |
| Normal Discharge | 350 LPH (@12V) |
| Nominal Head | 13.05 ft |
The supporting components and self-contained design makes some small differences in the pump specifications between the Corsair and Swiftech designs. Corsair has also selected a different fan to be integrated in the external cooler. The 1800 RPM Nautilus 500 fan has a maximum air flow of 74.4 CFM, which is slightly less than the 81.3 CFM of the Swiftech. However, static pressure is higher on the Corsair fan.
| 120mm Fan Specifications | |
| Fan Size | 120mm x 120mm x 25mm |
| Maximum Fan Speed | 1800 RPM |
| Maximum Airflow | 74.4 CFM |
| Current | 0.3A |
| Static Pressure | 32mm H2O |
| CPU Block | |
| Description | 100% solid copper supporting Delphi Micro-Channel Technology |
| Material | Solid Copper |
| Fittings | Built-in 3/8 in barbs |
The CPU clock looks very similar to the water block used in the Swiftech H2O-120 Compact. The Corsair design uses a stand-alone water block and does not integrate the block and pump as we saw in the Swiftech. This moves the pump noise from inside the case, as in the Swiftech, to outside the case in the cooling box on the Corsair. Which is the better design is a matter for debate, but as you'll see shortly we consider both designs noisier than the best air cooler designs.
There was no problem with fitting the Nautilus 500 waterblock to any motherboard we tested, and in fact we doubt you can find a motherboard that cannot mount the Corsair water block. Since the water block is standalone in the Corsair design there is no potential issue with side barbs as we saw on the Swiftech
Originally published at https://www.anandtech.com/show/2328 (Wayback Machine).