Archive 1997–2024

EVGA nForce 650i Ultra: Performance on a Budget

Overclocking - E4300

EVGA nForce 650i Ultra
E4300 Overclocking Testbed
Processor: Intel Core 2 Duo E4300
Dual Core, 1.86GHz, 2MB Unified Cache
800FSB, 9x Multiplier
CPU Voltage: 1.4625V (default 1.30V)
SPP Voltage: 1.40V
FSB Voltage: 1.40V
Cooling: Tuniq 120 Air Cooling
Power Supply: OCZ ProXStream 1000W
Memory: OCZ Flex XLC PC2-6400 (2x1GB)
Video Cards: 1 x MSI 8800GTX
Hard Drive: Western Digital 150GB 10,000RPM SATA 16MB Buffer
Case: Cooler Master CM Stacker 830
Maximum OC: 380x9 (3-4-4-9 1T, 760MHz)
3420MHz (+84% CPU)
.

Click to enlarge

We were able to reach a final benchmark stable setting of 9x380 FSB resulting in a clock speed of 3420MHz. Our E4300 is not the best of the lot and has not gone above 400FSB on several boards so we consider these results to be very good for our particular sample. We were able to POST and enter XP at 9x390 but could not complete our benchmark test suite.

We were able to run our OCZ Flex PC2-9200, OCZ Flex CAS3 PC2-6400, and our Corsair PC2-8888 at the reported timings with a 1T Command Rate enabled with 2.10 V. However, the memory had to be set to Sync mode in order to utilize these timings and command rate. With the memory voltage being limited to 2.1V, it was very difficult finding memory modules that would allow CAS3 and 1T command rate operation while overclocking the FSB. We also had to set the SPP voltage to 1.30V to ensure stability at 1T operation with all of our processors. Vdroop was very acceptable on this board during overclocking with an average drop of .02V during load testing with our E4300.

Overclocking - E6300

EVGA nForce 650i Ultra
E6300 Overclocking Testbed
Processor: Intel Core 2 Duo E6300
Dual Core, 1.86GHz, 2MB Unified Cache
1066FSB, 7x Multiplier
CPU Voltage: 1.4500V (default 1.3250V)
SPP Voltage: 1.50V
FSB Voltage: 1.40V
Cooling: Tuniq 120 Air Cooling
Power Supply: OCZ ProXStream 1000W
Memory: OCZ Flex XLC PC2-6400 (2x1GB)
Video Cards: 1 x MSI 8800GTX
Hard Drive: Western Digital 150GB 10,000RPM SATA 16MB Buffer
Case: Cooler Master CM Stacker 830
Maximum OC: 509x7 (3-4-4-10 2T, 793MHz)
3569MHz (+91% FSB/CPU)
.

Click to enlarge

Switching to an E6300, we reached a final setting of 7x509 FSB resulting in a clock speed of 3569MHz. We had to loosen our memory timings slightly while overclocking in order to maintain stability at the higher FSB rates. We were not able to run a command rate of 1T past 450FSB and attribute this to crosstalk on the board due to the four-layer design and a lack of memory voltages past 2.1V. We did notice in 4GB testing that we had to change our OCZ Flex PC2-6400 CAS3 memory timings to 4-4-3-10 2T at 2.10V for stable 24/7 operation in a variety of applications. Vdroop was acceptable during load testing with our E6300 with an average drop of .03V.

Originally published at https://www.anandtech.com/show/2207 (Wayback Machine).