Intel 945P Motherboards: Going from Hopeless to Enthusiastic
- Posted in
- Motherboards
EPOX 5LDA+GLI: Overclocking
FSB Overclocking Results
Memory Stress Tests
Memory stress tests look at the ability of the Epox 5LDA+GLI to operate at the officially supported memory frequencies of 667MHz DDR2 at the best performing memory timings that the Corsair CM2X512A-5400UL revision 1.3 will support.
The Epox 5LDA+GLI was completely stable with 2 DDR2 modules in Dual-Channel at the settings of 3-2-2-8 at 2.1V.
We will now install all four available memory slots, which are usually more strenuous on the memory subsystem than testing 2 DDR2 modules on a motherboard.
The Epox 5LDA+GLI was completely stable with 4 DDR2 modules in Dual-Channel at the settings of 3-4-4-8 and needed the voltage increased to 2.15V. This is a very good accomplishment for a board targeted at the mainstream market.
FSB Overclocking Results
| Front Side Bus Overclocking Testbed | |
| Processor: | Pentium 4 Prescott LGA 775 820 Dual Core 2.8GHz |
| CPU Voltage: | 1.4500V (1.3000V default) |
| Memory Settings: | 3-2-2-8 at 667MHz |
| Memory Voltage: | 2.15V |
| NorthBridge Voltage: | 1.60V |
| SouthBridge Voltage: | 1.00V |
| Cooling: | Intel 840EE Heat Sink |
| Power Supply: | OCZ Power Stream 520 |
| Maximum CPU OverClock: | 257fsb x 14 (3598MHz) +28% |


Memory Stress Tests
Memory stress tests look at the ability of the Epox 5LDA+GLI to operate at the officially supported memory frequencies of 667MHz DDR2 at the best performing memory timings that the Corsair CM2X512A-5400UL revision 1.3 will support.
| Epox 5LDA+GLI Stable DDR667 Timings - 2 DIMMs (2/4 slots populated - 1 Dual-Channel Bank) |
|
| Clock Speed: | 200MHz (800FSB) |
| Timing Mode: | 667MHz - Default |
| CAS Latency: | 3 |
| RAS to CAS Delay: | 2 |
| RAS Precharge: | 2 |
| RAS Cycle Time: | 8 |
| Voltage: | 2.1V |
The Epox 5LDA+GLI was completely stable with 2 DDR2 modules in Dual-Channel at the settings of 3-2-2-8 at 2.1V.
We will now install all four available memory slots, which are usually more strenuous on the memory subsystem than testing 2 DDR2 modules on a motherboard.
| Epox 5LDA+GLI Stable DDR667 Timings - 4 DIMMs (4/4 slots populated - 2 Dual-Channel Banks) |
|
| Clock Speed: | 200MHz (800FSB) |
| Timing Mode: | 667MHz - Default |
| CAS Latency: | 3 |
| RAS to CAS Delay: | 4 |
| RAS Precharge: | 4 |
| RAS Cycle Time: | 8 |
| Voltage: | 2.15V |
The Epox 5LDA+GLI was completely stable with 4 DDR2 modules in Dual-Channel at the settings of 3-4-4-8 and needed the voltage increased to 2.15V. This is a very good accomplishment for a board targeted at the mainstream market.
Originally published at https://www.anandtech.com/show/1857 (Wayback Machine).