Shuttle SN27P2 SFF: AM2 gets the Tiny Treatment
- Posted in
- Systems
Overclocking
While overclocking and SFF systems are rarely a great match, we did test the limits of the SN27P2 in this area. Here are our results.
The initial BIOS we received with the system did not have working CPU multipliers, which severely limited our overclocking attempts when using an Athlon X2 5000+ processor. The maximum HyperTransport bus speed is 300 MHz, but if you're stuck with a 13X multiplier you'll never get there. In fact, given that the 5000+ is near the top of AMD's current dual core chips, it should come as little surprise that we were not able to overclock more than 10% without difficulties. Even at such a small overclock, with the added voltage required for stability, noise levels when the CPU was placed under a full load were substantially higher.
Our recommendation is that if you plan on getting a dual core processor, don't plan on major overclocks -- not that we really expect most people to overclock small form factor systems, but it is worth mentioning. It appears that the cooling system simply isn't capable of dealing with the heat output generated from most overclocked X2 chips, though we did test the system briefly with an FX-62 and found that it worked without difficulty at stock speeds.
We got around the BIOS multiplier limitations by installing an Athlon 64 3000+ (default clock speed of 1.8 GHz). With the lower 9X multiplier and a single CPU core, we were able to overclock to 2.7 GHz, reaching the maximum supported bus speed. Unlike many of the AM2 motherboards we've tested, however, this was only possible by dropping the HyperTransport multiplier down to 3X. In this area, overclocking was similar to what we saw on the nForce4 platform: the HyperTransport bus really didn't want to run much over 1000 MHz, but given that the HTT bus is rarely a bottleneck in terms of system performance this isn't a major concern.
If for whatever reason you are interested in buying a cheap single core Athlon 64 and putting it in the SN27P2, it appears that the system is more than capable of overclocking such a processor. On the other hand, if you want to purchase a dual core processor, either don't plan on overclocking much, or purchase an X2 3800+ and plan on topping out at around 2.6 GHz (with a noisier system than if you were to simply buy a 5000+). It could also be that the forthcoming low-power X2 chips will overclock better and/or run quieter in this type of system, but as we have not been able to get a hold of any of these we cannot say for certain.
Memory Stress Testing
The overclocking features present on the SN27P2 are a bit more limited than what we see with many high-end motherboards, and CPU voltage tops out at 1.525V. Perhaps more importantly, the DDR2 memory voltage tops out at 2.0V. Our Corsair memory is rated at PC2-8500 with 5-5-5-18 timings, but we have been able to run this memory at DDR2-800 with 3-3-3-9 timings on several other motherboards when using 2.2-2.3V. We were able to run with 4-4-4-12 timings with the RAM set to 2.0V, but we could not drop the CAS/tRP/tRCD values to 3.0 (individually or together) with the limited voltage options.
The BIOS also only offers the standard memory timing adjustments (CAS/tRCD/tRP/tRAS), which further limits our ability to tweak for maximum performance. This may result in slightly lower performance relative to the top AM2 motherboards, but for the most part the differences should be minor and not something you would notice during actual use (without running benchmarks). If you are truly concerned about memory performance, your best bet is to purchase some PC2-6400 memory that is designed to run with low latencies at lower voltages (1.8-2.0V). That type of memory may or may not overclock as much as the Corsair memory we are using, but as we just demonstrated, overclocking really shouldn't be your primary concern with the SN27P2 - or any SFF computer, for that matter.
Testing with all four DIMM slots populated stresses the memory subsystem more, but as you can see we were still able to maintain 4-4-4-12 timings. Running with 4GB of memory (or more) is really only beneficial if you are running a 64-bit operating system, however, and for the time being we continue to prefer XP over XP x64. Let's not even talk about Windows Vista x64 Beta 2 performance. However, in another year we expect 4GB configurations to become far more common.
While overclocking and SFF systems are rarely a great match, we did test the limits of the SN27P2 in this area. Here are our results.
| Shuttle SN27P2 Overclocking | |
| Processor: | Athlon X2 5000+ (AM2) |
| Chipset: | nForce 570 Ultra |
| CPU Voltage: | 1.400V (1.300V default) |
| Memory Settings: | 5-5-5-15 2T DDR2-800 Setting |
| DDR2 Results: | 13 x 215HTT = DDR2-798 |
| HT Multiplier: | 4x above 200HTT |
| Memory Voltage: | 2.0V |
| Chipset Voltage: | 1.65V |
| Maximum CPU Overclock: | 13 x 215 = 2795 MHz |
| Shuttle SN27P2 Overclocking | |
| Processor: | Athlon 64 3000+ (AM2) |
| Chipset: | nForce 570 Ultra |
| CPU Voltage: | 1.525V (1.300V default) |
| Memory Settings: | 4-4-4-13 2T DDR2-400 |
| DDR2 Results: | 9 x 300HTT = DDR2-600 |
| HT Multiplier: | 4x above 210HTT, 3X above 260 HTT |
| Memory Voltage: | 2.0V |
| Chipset Voltage: | 1.70V |
| Maximum CPU Overclock: | 9 x 300 = 2700 MHz |
| Maximum HTT Overclock: | 300 MHz (50%) - BIOS maximum |
The initial BIOS we received with the system did not have working CPU multipliers, which severely limited our overclocking attempts when using an Athlon X2 5000+ processor. The maximum HyperTransport bus speed is 300 MHz, but if you're stuck with a 13X multiplier you'll never get there. In fact, given that the 5000+ is near the top of AMD's current dual core chips, it should come as little surprise that we were not able to overclock more than 10% without difficulties. Even at such a small overclock, with the added voltage required for stability, noise levels when the CPU was placed under a full load were substantially higher.
Our recommendation is that if you plan on getting a dual core processor, don't plan on major overclocks -- not that we really expect most people to overclock small form factor systems, but it is worth mentioning. It appears that the cooling system simply isn't capable of dealing with the heat output generated from most overclocked X2 chips, though we did test the system briefly with an FX-62 and found that it worked without difficulty at stock speeds.
We got around the BIOS multiplier limitations by installing an Athlon 64 3000+ (default clock speed of 1.8 GHz). With the lower 9X multiplier and a single CPU core, we were able to overclock to 2.7 GHz, reaching the maximum supported bus speed. Unlike many of the AM2 motherboards we've tested, however, this was only possible by dropping the HyperTransport multiplier down to 3X. In this area, overclocking was similar to what we saw on the nForce4 platform: the HyperTransport bus really didn't want to run much over 1000 MHz, but given that the HTT bus is rarely a bottleneck in terms of system performance this isn't a major concern.
If for whatever reason you are interested in buying a cheap single core Athlon 64 and putting it in the SN27P2, it appears that the system is more than capable of overclocking such a processor. On the other hand, if you want to purchase a dual core processor, either don't plan on overclocking much, or purchase an X2 3800+ and plan on topping out at around 2.6 GHz (with a noisier system than if you were to simply buy a 5000+). It could also be that the forthcoming low-power X2 chips will overclock better and/or run quieter in this type of system, but as we have not been able to get a hold of any of these we cannot say for certain.
Memory Stress Testing
| Shuttle XPC SN27P2 Stable DDR2-800 Timings - 2 or 4 DIMMs 2 or 4 slots populated - 1 or 2 Dual-Channel Bank(s) |
|
| HTT Clock Speed: | 200MHz |
| Timing Mode: | 800MHz |
| CAS Latency: | 4 |
| RAS to CAS Delay: | 4 |
| RAS Precharge: | 4 |
| RAS Cycle Time: | 13 |
| Command Rate: | 2T |
| Voltage: | 2.0V |
The overclocking features present on the SN27P2 are a bit more limited than what we see with many high-end motherboards, and CPU voltage tops out at 1.525V. Perhaps more importantly, the DDR2 memory voltage tops out at 2.0V. Our Corsair memory is rated at PC2-8500 with 5-5-5-18 timings, but we have been able to run this memory at DDR2-800 with 3-3-3-9 timings on several other motherboards when using 2.2-2.3V. We were able to run with 4-4-4-12 timings with the RAM set to 2.0V, but we could not drop the CAS/tRP/tRCD values to 3.0 (individually or together) with the limited voltage options.
The BIOS also only offers the standard memory timing adjustments (CAS/tRCD/tRP/tRAS), which further limits our ability to tweak for maximum performance. This may result in slightly lower performance relative to the top AM2 motherboards, but for the most part the differences should be minor and not something you would notice during actual use (without running benchmarks). If you are truly concerned about memory performance, your best bet is to purchase some PC2-6400 memory that is designed to run with low latencies at lower voltages (1.8-2.0V). That type of memory may or may not overclock as much as the Corsair memory we are using, but as we just demonstrated, overclocking really shouldn't be your primary concern with the SN27P2 - or any SFF computer, for that matter.
Testing with all four DIMM slots populated stresses the memory subsystem more, but as you can see we were still able to maintain 4-4-4-12 timings. Running with 4GB of memory (or more) is really only beneficial if you are running a 64-bit operating system, however, and for the time being we continue to prefer XP over XP x64. Let's not even talk about Windows Vista x64 Beta 2 performance. However, in another year we expect 4GB configurations to become far more common.
Originally published at https://www.anandtech.com/show/2038 (Wayback Machine).