Archive 1997–2024

DFI CFX3200-DR: ATI RD580 Tweak Attack

Overclocking


DFI CFX3200-DR
Overclocking Testbed
Processor: Athlon64 4000+
(2.4GHz, 1MB Cache)
CPU Voltage: 1.425V (default 1.35V)
Cooling: Thermaltake Silent Boost K8 Heatsink/Fan
Power Supply: OCZ Power Stream 520W
Memory: OCZ PC4800* Platinum (Samsung TCCD Memory Chips)
*The current equivalent OCZ memory to OCZ PC3200 Platinum Rev. 2
Hard Drive Hitachi 250GB 7200RPM SATA2 8MB Cache
Maximum OC:
(Standard Ratio)
246x12 (5x HT, 2.5-3-3-7)
2952MHz, 2 DIMMs in DC mode
(+23% CPU Overclock)
Maximum FSB:
(Lower Ratio)
315 x 9 (4x HT, 1T, 2.5-3-4-7)
2835MHz, 2 DIMMs in DC mode
(+58% Bus Overclock)


In most cases current NVIDIA and ATI chipsets need to have Hyper Transport frequency adjusted to 3X around a 300 Clock frequency to keep HT speed around 1000. The RD580 chipset was designed for higher HT speed. We consistently found the DFI board, like the recently tested ASUS A8R32-MVP based on the same RD580 chipset, could easily handle HT speeds in the 1450 to 1550 range. For most overclocking that means that it is not necessary to even adjust the 5X HT setting. It was only where we were exceeding around 1500 (300 Clock Frequency) that we had to drop the HT one notch to 4X. Overclockers should be very happy with this feature of the RD580 chipset.

It was previously reported that the RD580 chipset will not reset an HTT strap or ratio unless you first power down. We had first seen this in other testing of the RD580 Reference board and it was also the case in our review of the ASUS A8R32-MVP. For instance, if you try to set the ratio to 4X (from 5X), the board will not implement the ratio change until you have powered down the system. Engineers at DFI have found a clever way around this issue. They implement a power down and restart as part of the normal reboot sequence. This is very similar to the method used by ASUS and others in getting around the overclock locks on the 925x chipset. We mention this because at first it appeared the board was a very slow booter compared to similar boards. In fact the extra time is for a complete power down and start so BIOS options are properly implemented on boot. The delay might be annoying for frequent reboots, but most enthusiasts spend time getting their systems properly configured and then seldom shut down/reboot. An extra 5-10 second delay before hours of computer use isn't something we're concerned about.

The DFI CFX3200-DR required a few special adjustments for overclocks of 300 and beyond. Under "Genie BIOS Setting", "DRAM Configuration" "Max Asynch Latency" should be set to 4.5 to 6 for high overclocks. "Read Preamble Time", just below this setting, should be set to 7 to 10. The Auto setting for both options is too fast on early BIOS revisions, but Auto actually sets these more reasonable figures beginning with the 417 BIOS.

While we did not achieve the highest overclocks ever with the DFI CFX3200-DR, we suspect we could have achieved anything with this board if we had the weeks to invest in testing and tweaking the huge array of adjustments that are available. We were frankly overwhelmed by the array of adjustments as already mentioned in the Features discussion. It is wonderful to have such fine levels of control if you need and want it, but it is quite another to be forced to master these control levels to achieve maximum overclocks on this board.

The DFI BIOS really needs auto settings that work for the majority of situations with finer levels of control available if you want them. In many areas "Auto" is fine on the CFX3200-DR, but in other areas Auto is too aggressive or too related to a specific memory or CPU. It will likely take a few more BIOS revisions before the DFI will be a good board for both the budding overclocker and the veteran computer enthusiast. Overclocking has been part of computers for most of the AT staff since the Celeron 300 days or even earlier. However, the DFI adjustments are more than we will ever use and far too difficult to test and master. After complaining loudly for more OC options on boards, we're a little embarrassed to say this board is too much, but we think it will bring most users, even well-informed users, to psychotic episodes with 32 levels of drive strength, and DQS skew levels of +/- 0 to 255 in 511 levels.

Something for DFI to consider is the mechanism used by Gigabyte. Gigabyte has hidden their advanced BIOS options under special menus that only become visible by pressing Ctrl+F1. While we're not huge fans of that mechanism for normal BIOS adjustments - like basic memory timings - there are definitely options on the CFX3200-DR that could be hidden. It would be nice to get a "regular" BIOS that has adjustments similar to DFI's Infinity line available, and then an "advanced" mode could be used to display the additional options. Our only comment is that the "advanced" mode should be clearly documented within the BIOS, as many people newer to computers are unaware of the Ctrl+F1 feature of Gigabyte boards.

Originally published at https://www.anandtech.com/show/2002 (Wayback Machine).