Archive 1997–2024

VIA PT880 PRO: Biostar’s Deluxe Dual Combo

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Processor: Pentium 4 Smithfield LGA 775
840EE Dual Core 3.2GHz
CPU Voltage: 1.450V (1.4000v default)
Memory Settings: 3-2-2-8 at 533MHz
Memory Voltage: 2.1V
SPP Voltage: 1.58V
FSB Voltage: 1.40V
Cooling: Zalman CNPS 9500
Power Supply: OCZ Power Stream 520
Maximum CPU OverClock: 222fsb x 16 (3553MHz) +11%
Maximum FSB OverClock: 205fsb x 14 (2870MHz) +2%

This board is a dismal overclocker when comparing it to the Intel or NVIDIA based chipsets. At these overclock settings, the system was able to complete all of our benchmark test suites three consecutive times and run Prime95 and SuperPI without issue. We lowered the CPU multiplier to 14, but we could not overclock past a 205MHz FSB setting with either DDR2 or DDR memory. We strongly recommend that anyone interested in this board leaves the system at stock settings and to forget any thoughts of overclocking.


Memory Stress Testing

This memory stress test looks at the ability of the Biostar PT880 Pro-A7to operate at the officially supported memory frequencies of 533MHz DDR2, at the best performing memory timings that the Corsair CM2X512A-5400UL revision 1.3 will support. Note that this memory is rated at 3-2-2-8 timings.

Biostar PT880 Pro-A7 Combo
Stable DDR2-533 Timings - 2 DIMMs
(2/2 slots populated - 1 Dual-Channel Bank)
Clock Speed: 200MHz (800FSB)
Timing Mode: 533MHz - Default
CAS Latency: 3
RAS to CAS Delay: 2
RAS Precharge: 2
RAS Cycle Time: 8
Voltage: 2.1V

The Biostar TForce4 was very stable with 2 DDR2 modules in Dual-Channel at the settings of 3-2-2-8 at 2.1V. We will now test 2 DDR modules to determine our best performance settings.

This memory stress test looks at the ability of the Biostar PT880 Pro-A7 to operate at the officially supported memory frequencies of 400MHz DDR, at the best performing memory timings that the OCZ PC4800 Platinum Edition will support. This memory is rated for 2-2-2-5 timings.

Biostar PT880 Pro-A7 Combo
Stable DDR-400 Timings - 2 DIMMs
(2/2 slots populated - 2 Dual-Channel Banks)
Clock Speed: 200MHz
Timing Mode: 400MHz - Default
CAS Latency: 2.5
RAS to CAS Delay: 3
RAS Precharge: 2
RAS Cycle Time: 7
Command Rate: 1T
Voltage: 2.8V

The Biostar PT880 Pro-A7 was completely stable with 2 DDR modules in Dual-Channel operation at the settings of 2.5-3-2-7, but it required the memory to be operated at 2.8V. We tried several combinations of memory settings at CAS Latency settings of 2, but the board was not stable enough to complete our test suite.

Given the budget nature of this motherboard, it is unlikely that potential buyers would actually purchase top-quality memory. It is not uncommon to see value boards that are tuned for value components, and this appears to be the case with this Biostar board. Our recommendation is that you plan to run more typical memory timings, so unless you already have some better RAM, don't spend extra money getting high performance RAM for this motherboard.

Originally published at https://www.anandtech.com/show/1974 (Wayback Machine).