Archive 1997–2024

Intel 925X Roundup: Creative Engineering 101


DFI LANParty 925X-T2: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Processor: Pentium 4 Prescott LGA 775
2.8GHz
CPU Voltage: 1.3875V (default)
Cooling: Thermaltake Jungle 502
Power Supply: HiPro 470W
Maximum OC: 265FSB (+33%)

Like Asus and Abit, DFI manipulates the PCIe frequency during boot to achieve higher overclocks. The DFI was able to reach a FSB of 265, a 40% overclock, with an ATI X800 XT and SATA hard drive. This is the second highest overclock that we achieved with this hardware in the roundup. The LANParty 925X-T2 was more limited with an nVidia 6800 Ultra video card, reaching 248. As we have already stated, the nVidia PCIe cards are apparently less tolerant of out-of-spec PCIe frequency than the X800 XT.

DFI was able to achieve even higher overclocks with PCIe and SATA drives in their own lab tests, but we are finding that the PCI Express cards do vary a good bit in their ability to handle out-of-spec PCIe speeds. We used the same ATI X800 XT for all overclock tests in this roundup, so results could be compared one board to another.

The LGA 775 CPUs are multiplier locked, so the only way to overclock the CPU is to increase the FSB, but most manufacturers are floating the PCIe to achieve higher overclocks by manipulating CPU clock/PCIe ratios. All of the successful 925X overclockers are saying that fixing the frequency tends to limit the overclocking of the 925X to around 10%.

Memory Stress Test Results:

The memory stress test measures the ability of the DFI 925X-T2 to operate at its officially supported memory frequency (533MHz DDR2), at the best performing memory timings that Crucial/Micron PC2-4300U will support. Memory stress testing was conducted by running DDR2 at 533MHz (stock 3:4 ratio) with 2 DIMM slots operating in Dual-Channel mode.

Stable DDR533 Timings - 2 DIMMs
(2/4 DIMMs - 1 Dual-Channel Bank)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 3.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10*
Command Rate: N/A
*SPD (Auto) timings for DDR2 are normally 4-4-4-12 at DDR2-533. A tRAS setting of 12 is normal. We ran a series of tests to measure memory bandwidth, and found the tRAS setting made very little difference in the performance of DDR2. The most effective range of tRAS was 8 to 13 for DDR2 on the 925X chipset, so a tRAS of 10 was chosen for benchmarking.

DFI also performs without issue at the best 3-3-3-10 DDR2 timings that work well on all the 925X boards in the roundup.

Filling all four available memory slots is more strenuous on the memory sub-system than testing 2 DDR2 modules on a motherboard.

Stable DDR533 Timings - 4 DIMMs
(4/4 DIMMs - 2 Dual-Channel Banks)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 4.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10
Command Rate: N/A

The DFI LANParty 925X-T2 handled 4 DDR2 DIMMs at default voltage, at 4-3-3-10 timings, the same timings required on the Asus and Abit boards. It is very early in our testing of DDR2 memory - too early to draw firm broad conclusions - but it looks as if DDR2 memory may require slower timings with 4 DIMMs than what we can achieve with 2 DIMMs. Since we are accustomed to similar timings with either 2 or 4 DIMMs with regular DDR memory, this is a bit of a disappointment.

Originally published at https://www.anandtech.com/show/1431 (Wayback Machine).