Archive 1997–2024

Intel 925X Roundup: Creative Engineering 101


Asus P5AD2 Premium: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Processor: Pentium 4 Prescott LGA 775
2.8GHz
CPU Voltage: 1.3875V (default)
Cooling: Thermaltake Jungle 502
Power Supply: HiPro 470W
Maximum OC: 280FSB (+40%)

The LGA 775 CPUs are multiplier locked, so the only way to overclock the CPU is to increase the FSB. Fixing the PCIe frequency tends to limit the overclocking of the 925X, so Asus, like others in the roundup, allows the PCI Express frequency to float. Asus then manipulates the PCIe frequency (or ratios to be more precise) during boot to achieve higher overclocks. For more information on how Asus manages to reach such outstanding overclock with the P5AD2, please check Breaking Intel's Overclock Lock: The REAL Story.

The Asus was able to reach a FSB of 280, a 40% overclock, with an ATI X800 XT and SATA hard drive. This is by far the highest overclock that we achieved with this hardware in the roundup. The P5AD2 was more limited with an nVidia 6800 Ultra video card, reaching 258. The nVidia appears to be less tolerant of out-of-spec PCIe frequency than the X800 XT.

Memory Stress Test Results:

The memory stress test measures the ability of the Asus P5AD2 to operate at its officially supported memory frequency (533MHz DDR2), at the best performing memory timings that Crucial/Micron PC2-4300U will support. Memory stress testing was conducted by running DDR2 at 533MHz (stock 3:4 ratio) with 2 DIMM slots operating in Dual-Channel mode.

Stable DDR533 Timings - 2 DIMMs
(2/4 DIMMs - 1 Dual-Channel Bank)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 3.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10*
Command Rate: N/A
*SPD (Auto) timings for DDR2 are normally 4-4-4-12 at DDR2-533. A tRAS setting of 12 is normal. We ran a series of tests to measure memory bandwidth, and found the tRAS setting made very little difference in the performance of DDR2. The most effective range of tRAS was 8 to 13 for DDR2 on the 925X chipset, so a tRAS of 10 was chosen for benchmarking.

The Asus P5AD2 Premium was completely stable with 2 DDR2 modules in Dual-Channel at the settings of 3-3-3-10 at 1.8V default voltage. This matches the best timings that all the motherboards in this roundup were able to achieve with DDR2 memory. 3-3-3 is also faster than the specified 4-4-4 timings specified for the Crucial/Micron DDR2 modules used for these benchmarks.

Filling all four available memory slots is more strenuous on the memory sub-system than testing 2 DDR2 modules on a motherboard.

Stable DDR533 Timings - 4 DIMMs
(4/4 DIMMs - 2 Dual-Channel Banks)
Clock Speed: 266MHz
Timing Mode: N/A
CAS Latency: 4.0
Bank Interleave: N/A
RAS to CAS Delay: 3
RAS Precharge: 10T*
Precharge Delay: 3.0
Command Rate: N/A
*SPD (Auto) timings for DDR2 are normally 4-4-4-12 at DDR2-533. A tRAS setting of 12 is normal. We ran a series of tests to measure memory bandwidth, and found the tRAS setting made very little difference in the performance of DDR2. The most effective range of tRAS was 8 to 13 for DDR2 on the 925X chipset, so a tRAS of 10 was chosen for benchmarking.

As we first saw on the Abit, 4 DDR2 DIMMs are not stable at CAS 3 as 2 DIMMs are. Once again, we required 4-3-3 timings when using 4 DDR2 DIMMs, though 4-3-3 worked fine at default voltage. Perhaps more voltage could improve stability at 3-3-3 with 4 DIMMs, but our tests up to 2.0V (from default 1.8V) did not produce enough stability to complete our Super Pi or Aquamark 3 at the 3-3-3 timings.

Originally published at https://www.anandtech.com/show/1431 (Wayback Machine).