Archive 1997–2024

Intel 925X Roundup: Creative Engineering 101


Gigabyte 8ANXP-D: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Processor: Pentium 4 Prescott LGA 775
2.8GHz
CPU Voltage: 1.3875V (default)
Cooling: Thermaltake Jungle 502
Power Supply: HiPro 470W
Maximum OC: 255FSB (+28%)

The only way to overclock an Intel CPU is to increase the FSB. When we first tested the Gigabyte, the overclock limit was less than 10%, 218 to be precise. With no adjustment for PCIe frequency, it appeared Gigabyte was fixing the PCIe bus, but they did have PCIe word overclocks like "PCIe Turbo". We went through several BIOS revisions to finally reach where Gigabyte is today, reaching 255 with the ATI X800 XT. However, the nVidia 6800 Ultra on the Gigabyte is still pretty mediocre at a maximum overclock of 228.

These results indicate Gigabyte is probably using a different approach to getting around the 10% OC issue. That also means that we may see even more improvement in the 8ANXP-D overclocking performance in the future.

Memory Stress Test Results:

The memory stress test measures the ability of the Gigabyte 8ANXP-D to operate at its officially supported memory frequency (533MHz DDR2), at the best performing memory timings that Crucial/Micron PC2-4300U will support. Memory stress testing was conducted by running DDR2 at 533MHz (stock 3:4 ratio) with 2 DIMM slots operating in Dual-Channel mode.

Stable DDR533 Timings - 2 DIMMs
(2/4 DIMMs - 1 Dual-Channel Bank)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 3.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10*
Command Rate: N/A
*SPD (Auto) timings for DDR2 are normally 4-4-4-12 at DDR2-533. A tRAS setting of 12 is normal. We ran a series of tests to measure memory bandwidth, and found the tRAS setting made very little difference in the performance of DDR2. The most effective range of tRAS was 8 to 13 for DDR2 on the 925X chipset, so a tRAS of 10 was chosen for benchmarking.

Like the other 925X motherboards in this roundup, the Gigabyte was completely stable with 2 DDR2 modules at the best performing settings of 3-3-3-10 at default speed and 1.8V default voltage.

Filling all four available memory slots is more strenuous on the memory sub-system than testing 2 DDR2 modules on a motherboard.

Stable DDR533 Timings - 4 DIMMs
(4/4 DIMMs - 2 Dual-Channel Banks)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 4.0
Bank Interleave: Auto
RAS to CAS Delay: 4
RAS Precharge: 3
Cycle Time (tRAS): 10
Command Rate: N/A

The Gigabyte board required 4-4-3 timings for complete stability at default voltage with 4 DIMMs. This is slightly slower than the best boards in the roundup with 4 DIMMs, but it is very close to the best 4-3-3 settings. As was said in the Foxconn review, the next Gigabyte 8ANXP-D that we test might well do 4-3-3 timings with 4 DIMMs, as it could just as well be explained as normal production variation in 925X chipsets or Gigabyte motherboards. This small difference in memory timings is not really that significant.

Originally published at https://www.anandtech.com/show/1431 (Wayback Machine).