Archive 1997–2024

Four Multi-GPU Z77 Boards from $280-$350 - PLX PEX 8747 featuring Gigabyte, ASRock, ECS and EVGA

System Benchmarks

USB Speed

For this benchmark, we run CrystalDiskMark to determine the ideal sequential read and write speeds for the USB port using our 240 GB OCZ Vertex3 SSD with a SATA 6 Gbps to USB 3.0 converter.  Then we transfer a set size of files from the SSD to the USB drive using DiskBench, which monitors the time taken to transfer.  The files transferred are a 1.52 GB set of 2867 files across 320 folders – 95% of these files are small typical website files, and the rest (90% of the size) are the videos used in the Sorenson Squeeze test. 

USB 2.0 Sequential Read Speeds

USB 2.0 Sequential Write Speeds

USB 2.0 Copy Time

The obvious outlier in what should be a relatively simple USB 2.0 test is the ECS Z77H2-AX.  For some unknown reason, it suffers a limited USB 2.0 speed at a round 25 MBps either read or write.  To a certain extent, the EVGA also has some problems in USB 2.0 write.

USB 3.0 Sequential Read Speeds

USB 3.0 Sequential Write Speeds

USB 3.0 Copy Time

The USB 2.0 problems are not present at all in USB 3.0 testing, with each of the boards performing similarly.

SATA Testing

We also use CrystalDiskMark for SATA port testing on a C300 drive.  The sequential test (incompressible data) is run at the 5 x 1000 MB level.  This test probes the efficiency of the data delivery system between the chipset and the drive, or in the case of additional SATA ports provided by a third party controller, the efficiency between the controller, the chipset and the drive.

SATA 3 Gbps Sequential Read Speeds

SATA 3 Gbps Sequential Write Speeds

SATA 6 Gbps Sequential Read Speeds

SATA 6 Gbps Sequential Write Speeds

The EVGA Z77 FTW motherboard has issues in SATA write tests, similar to the MSI previously tested.

DPC Latency

Deferred Procedure Call latency is a way in which Windows handles interrupt servicing.  In order to wait for a processor to acknowledge the request, the system will queue all interrupt requests by priority.  Critical interrupts will be handled as soon as possible, whereas lesser priority requests, such as audio, will be further down the line.  So if the audio device requires data, it will have to wait until the request is processed before the buffer is filled.  If the device drivers of higher priority components in a system are poorly implemented, this can cause delays in request scheduling and process time, resulting in an empty audio buffer – this leads to characteristic audible pauses, pops and clicks.  Having a bigger buffer and correctly implemented system drivers obviously helps in this regard.  The DPC latency checker measures how much time is processing DPCs from driver invocation – the lower the value will result in better audio transfer at smaller buffer sizes.  Results are measured in microseconds and taken as the peak latency while cycling through a series of short HD videos - under 500 microseconds usually gets the green light, but the lower the better.

DPC Latency Maximum

A trend worth noting is that all PLX PEX 8747 motherboards have some additional DPC latency compared to their brethren.  Any score below 500 microseconds is good, but under 200 microseconds is better.  The EVGA and the ECS fall outside this region with the two worst DPC scores on Z77.  The best of the boards tested in this roundup comes with the ASRock Z77 Extreme9.

 

Originally published at https://www.anandtech.com/show/6170/four-multigpu-z77-boards-from-280350-plx-pex-8747-featuring-gigabyte-asrock-ecs-and-evga (Wayback Machine).