SilverStone Strider Plus - 500W Modular Power
Voltage Regulation
| +3.3V Regulation/Ripple and Noise | |
| Load | Voltage |
| 10% | +2,73% (4mV) |
| 20% | +2,12% (8mV) |
| 50% | +0,91% (12mV) |
| 80% | -0,91% (16mV) |
| 100% | -1,81% (19mV) |
| 110% | -2,42% (22mV) |
| Crossload +12V max. | +1,51% |
| Crossload +3,3V/+5V max. | +2,73% |
| +5V Regulation/Ripple and Noise | |
| Load | Voltage |
| 10% | +2,20% (7mV) |
| 20% | +1,80% V (11mV) |
| 50% | +1,80% (14mV) |
| 80% | +1,20% (15mV) |
| 100% | +1,20% (18mV) |
| 110% | +1,00% (20mV) |
| Crossload +12V max. | +2,40% |
| Crossload +3,3V/+5V max. | -5,20% |
| +12V Regulation (Worst Rail)/Ripple and Noise (Worst Rail) | |
| Load | Voltage |
| 10% | +0,92% (9mV) |
| 20% | +1,01% (18mV) |
| 50% | +0,42% (35mV) |
| 80% | -1,08% (43mV) |
| 100% | -1,25% (58mV) |
| 110% | -1,58% (63mV) |
| Crossload +12V max. | -3,25% |
| Crossload +3,3V/+5V max. | +9,83% |
Noise Levels
| Sound Pressure Level (Ambient: 16dBA, 1m distance) | |
| Load | dB(A) |
| 10% | 20 |
| 20% | 20 |
| 50% | 20 |
| 80% | 26 |
| 100% | 30 |
| 110% | 32 |
Efficiency and PFC
| 115VAC, 60Hz | ||
| Load | Efficiency | PFC |
| 10% | 77% | 0.944 |
| 20% | 83% | 0.957 |
| 50% | 86% | 0.972 |
| 80% | 85% | 0.981 |
| 100% | 82% | 0.987 |
| 110% | 81% | 0.991 |
| 230VAC, 50Hz | ||
| Load | Efficiency | PFC |
| 10% | 79% | 0.822 |
| 20% | 84% | 0.940 |
| 50% | 87% | 0.970 |
| 80% | 86% | 0.978 |
| 100% | 85% | 0.986 |
| 110% | 83% | 0.988 |
The SilverStone Strider Plus 500W can deliver the specified power and even a bit more. The ripple and noise is low on all outputs, especially on +3.3V and +5V where less than 0.44% can be achieved. The efficiency is likewise well above the necessary values for 80 Plus Bronze. Only the measurements at 10% load are low on both power grids. Of course, 77-79% efficiency at 50W means you're drawing 63-65W from the wall; improving efficiency to 83% would cut power use to 60W, so the potential savings aren't all that noteworthy. The power factor reaches a maximum of 0.991, again with rather low PFC at 10% load on 230VAC.
Under load the power supply is clearly audible, and fan speed starts to ramp up once you reach 50% load. However, there isn't any background noise from the electronics, which is good. During the crossload tests +5V and +12V were out of the ATX specification. During test 2 +5V was significantly increased by the regulation circuit (still far away from 5.00V), but +12V was raised too. However, this is not a problem that concerns SilverStone only. The forward converter with coupled outputs, as it is used in most power supplies, has complications with crossload tests. In the future we will see that many 80 Plus Gold power supplies are better--and not just because of the higher efficiency. This is the reason for our new test procedure.
Originally published at https://www.anandtech.com/show/4908/silverstone-strider-plus-500w-modular-power (Wayback Machine).