Archive 1997–2024

1GB DIMMs: FAST 2GB DDR Kits from Corsair, Gigaram, and OCZ

Why 1GB DIMMs?

In past memory reviews, we have said a lot about the impact of the 2T Command Rate on memory performance. We have speculated with others that the Rev. E AMD processor would remove the 2T requirement for 4 DIMMs, but in fact, the release Rev. E still required a 2T Command Rate with 4 DIMMs on the new on-CPU memory controller. So, what is the impact of going from 1T with 2 DIMMs to 2T with 4 DIMMs?

Here, you see tests of 2 vs. 4 DIMMs of our standard OCZ PC3200 Platinum Rev. 2 based on Samsung TCCD memory chips. In all tests, the timings were 2-2-2-7 and the only difference was the 1T Command Rate with 2 DIMMs and 2T with 4 DIMMs:

Quake3 fps Sandra UNBuffered Sandra Standard Buffered Super PI 2M places
(time in sec)
Wolfenstein - Radar - Enemy Territory fps
2x512MB
2-2-2-7
2.6V 1T
550.2 INT 2621
FLT 2738
INT 5984
FLT 5938
80 121.1
4x512MB
2-2-2-7
2.6V 2T
529.6 INT 2276
FLT 2362
INT 4925
FLT 5938
83 116.9
1T Performance Increase 3.9% 15.5% 21.1% 3.8% 3.6%

For best comparison, we reran all benchmarks with the exact same settings for 2 DIMMs and 4 DIMMs, the only difference being 1T or 2T timings. We could have achieved faster timings (and a bigger performance difference) by tweaking each set of tests for best bandwidth. Therefore, these should be considered best case (lowest) performance differences.

As you can clearly see, the memory-only Sandra tests show a 21% drop in memory bandwidth in the standard buffered test when reducing to a 2T Command Rate. The more real-world Unbuffered Sandra test still shows a 15.5% bandwidth drop. Games and Super Pi, where memory is just one small component of the overall result, show about a 4% performance reduction. These represent the impact of this memory change on the overall system performance, where the Sandra scores measure impact on memory alone.

The second area where 4 DIMMs have a significant impact compared to 2 DIMMs is overclocking. This won't matter to those who run their systems at stock speeds, but it will be very important to those who try to squeeze the best performance from their memory. Here, we compared overclocking with our stock OCZ PC3200 Platinum Rev. 2 with 2 and 4 DIMMs. Again, we kept timings and settings exactly the same.

Highest Overclock at 9X Ratio
(4000+ Rev. E)
2x512MB
2.5-4-3-7 1T
318 (DDR636)
4x512MB
2.5-4-3-7 2T
240 (529.6)
2 DIMM Performance Increase 295%

Using the same DIMMs and same timings, we could only reach a 240 Processor Clock or +20% with 4 DIMMs. Two DIMMs allowed an overclock to 318 or +59%. With two DIMMs, we could overclock almost 3 times higher than with 4 DIMMs. You can likely overclock a bit higher with 4 DIMMs by further tweaking memory timings, but 4 DIMM overclocking will always fall far short of 2 DIMMs on current Athlon 64 memory controllers.

Higher performance at 1T vs. 2T and higher overclocking potential are certainly strong motivations to use 1GB DIMMs instead of 512Mb DIMMs when you want to populate an Athlon 64 board with 2GB. However, the gain of 1T in the past has often been more than offset by the slow memory timings available on 1GB DIMMs. The Athlon 64 controller is much lower latency than current Intel solutions, and thus, is much more bandwidth-sensitive to memory timings than a comparable Intel solution. We have shown in past memory reviews that slower memory timings can more than offset the 3.6% to 3.9% real-world performance loss that results in 4 DIMMs at 2T Command Rate. However, the availability of DDR400 1GB DIMMs rated as fast as 2-3-2 at DDR433 certainly has the potential to change this picture.

Originally published at https://www.anandtech.com/show/1817 (Wayback Machine).