ATI’s Crossfire: Best Overclocker on the Market?
- Posted in
- CPUs
Firewire and USB Performance
It is really difficult to put together a simple, repeatable, and consistent test to measure USB and Firewire Performance. Since our goal was to make this a standard part of motherboard testing, we needed a benchmark that was reasonably simple to run and that would also provide consistent results on the same test bed. We finally determined that an external USB 2.0, Firewire 400, and Firewire 800 hard disk might be a sensible way to look at USB and Firewire throughput.
Our first efforts at testing with an IDE or SATA drive as the “server” yielded very inconsistent results, since Windows XP sets up cache schemes to improve performance. Finally, we asset up a RAM disk as our “server”, since memory removed almost all overhead from the serving end. We also managed to turn off disk caching on the USB and Firewire side by setting up the drives for “quick disconnect” and our results were then consistent over many test runs.
We used just 1GB of fast 2-2-2 system memory set up as a 450MB RAM disk and 550MB of system memory. Our stock file was the SPECviewPerf install file, which is 432,533,504 bytes (412.4961MB). After copying this file to our RAM disk, we measured the time for writing from the RAM disk to our external USB 2.0 or Firewire 400 or Firewire 800 drive using a Windows timing program written for AnandTech by our own Jason Clark. The copy times in seconds were then converted into Megabits per second (Mb) to provide a convenient means of comparing throughput. Higher Rates therefore mean better performance.
Perhaps the biggest surprise in our testing was the poor performance of USB 2.0 on the ATI Crossfire AMD. ATI had promised improvement in USB performance in the SB450 compared to the earlier SB400, but we could see little improvement in our USB 2.0 tests. ATI responded that our USB 2.0 tests measured sustained throughput, which is relevant in USB operations only with applications like the USB 2.0 hard drive that we use for this test. ATI claims that burst USB 2.0 throughput has been improved in the SB450 to near the same levels of competitive USB 2.0 peak performance. We could not confirm these claims with any test procedures. Perhaps more important, ATI is aware of the issues with USB 2.0 performance and these will be fully corrected – sustained and peak performance – in the SB600 south bridge. It appears that this issue of USB performance may also be corrected by combining the ATI RD480 northbridge with the just released ULi M1575 Southbridge.
Since our ramdisk/apptimer File Copy is measuring sustained throughput, we also compared performance of ATI IDE/SATA/Sil SATA2 using this same test procedure. The performance of ATI IDE remains excellent, but SATA and SATA 2 performance are very competitive, but not standout as in the iPeak storage benchmarks of the same controllers.
It is really difficult to put together a simple, repeatable, and consistent test to measure USB and Firewire Performance. Since our goal was to make this a standard part of motherboard testing, we needed a benchmark that was reasonably simple to run and that would also provide consistent results on the same test bed. We finally determined that an external USB 2.0, Firewire 400, and Firewire 800 hard disk might be a sensible way to look at USB and Firewire throughput.
Our first efforts at testing with an IDE or SATA drive as the “server” yielded very inconsistent results, since Windows XP sets up cache schemes to improve performance. Finally, we asset up a RAM disk as our “server”, since memory removed almost all overhead from the serving end. We also managed to turn off disk caching on the USB and Firewire side by setting up the drives for “quick disconnect” and our results were then consistent over many test runs.
We used just 1GB of fast 2-2-2 system memory set up as a 450MB RAM disk and 550MB of system memory. Our stock file was the SPECviewPerf install file, which is 432,533,504 bytes (412.4961MB). After copying this file to our RAM disk, we measured the time for writing from the RAM disk to our external USB 2.0 or Firewire 400 or Firewire 800 drive using a Windows timing program written for AnandTech by our own Jason Clark. The copy times in seconds were then converted into Megabits per second (Mb) to provide a convenient means of comparing throughput. Higher Rates therefore mean better performance.
Perhaps the biggest surprise in our testing was the poor performance of USB 2.0 on the ATI Crossfire AMD. ATI had promised improvement in USB performance in the SB450 compared to the earlier SB400, but we could see little improvement in our USB 2.0 tests. ATI responded that our USB 2.0 tests measured sustained throughput, which is relevant in USB operations only with applications like the USB 2.0 hard drive that we use for this test. ATI claims that burst USB 2.0 throughput has been improved in the SB450 to near the same levels of competitive USB 2.0 peak performance. We could not confirm these claims with any test procedures. Perhaps more important, ATI is aware of the issues with USB 2.0 performance and these will be fully corrected – sustained and peak performance – in the SB600 south bridge. It appears that this issue of USB performance may also be corrected by combining the ATI RD480 northbridge with the just released ULi M1575 Southbridge.
Since our ramdisk/apptimer File Copy is measuring sustained throughput, we also compared performance of ATI IDE/SATA/Sil SATA2 using this same test procedure. The performance of ATI IDE remains excellent, but SATA and SATA 2 performance are very competitive, but not standout as in the iPeak storage benchmarks of the same controllers.
Originally published at https://www.anandtech.com/show/1800 (Wayback Machine).