Archive 1997–2024

nForce4 SLI Roundup: Painful and Rewarding


Gigabyte K8NXP-SLI: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Gigabyte K8NXP-SLI
Processor: Athlon 64 4000+
(2.4GHz, 1MB Cache)
CPU Voltage: 1.55V (default 1.50V)
Cooling: Thermaltake Silent Boost K8 Heat sink/Fan
Power Supply: OCZ Power Stream 520W
Memory: OCZ PC3200 EL Platinum Rev. 2
(Samsung TCCD Memory Chips)
Hard Drive: Seagate 120GB 7200RPM SATA 8MB Cache
Maximum OC:
(Standard Ratio)
230x12 (4X HT, 2.5-3-2-7, 1T, 2.8V)
2760MHz (+15%)
Maximum FSB:
(Lower Ratio)
230x12 (2760MHz) (4X HT, 2.5-3-2-7, 2.8V)
(1:1 Memory, 1T, 2 DIMMs in DC mode)
(+15% Bus Overclock)

After the excellent overclocking results that we found in our pre-production review of the K8NXP-SLI, we really expected the Gigabyte SLI to be near the top of our overclocking charts. However, something has happened along the way from pre-production to production because our production board could only reach a very disappointing 230 CPU speed regardless of the multiplier selected. This is in stark contrast to the 284 that we easily reached on the pre-production board.

We recently met with Gigabyte to discuss this issue and Gigabyte has assured us that they will make updates to get overclocking back to the levels which we saw in our earlier review. For now, we can only say that we have no idea what you will actually find in the overclocking capabilities of a K8NXP-SLI that you might buy. It could be stellar, like the pre-production board that we tested, or mediocre, like the last board that we tested. We have evidence to support either conclusion.

Memory Stress Test Results:

Our memory stress tests measure the ability of the K8NXP-SLI to operate at its officially supported memory frequency (400MHz DDR), at the lowest memory timings that OCZ PC3200 Platinum Rev. 2 modules will support. All DIMMs used for stress testing were 512MB double-sided (or double-bank) memory. To make sure that memory performed properly in Dual-Channel mode, memory was only tested using either one dual-channel (2 DIMMs) or 2 dual-channels (4 DIMMs).

Stable DDR400 Timings - One Dual-Channel
(2/4 DIMMs populated)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 7T
Precharge Delay: 2T
Command Rate: 1T

Using two DIMMs in Dual-Channel 128-bit mode, the memory performed in all benchmarks at the fastest 2-2-2-7 timings, at default 2.6 voltage.

Tests with 4 DS DIMMs on an AMD Athlon 64 system are more demanding, since AMD specifies DDR333 for this combination. However, most AMD Athlon 64 motherboards combined with recent AMD processors (the memory controller is on the AMD CPU) have been able to handle 4 DIMMs at DDR400.

Stable DDR400 Timings - 4 DIMMs
(4/4 DIMMs populated)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 7T
Precharge Delay: 2T
Command Rate: 2T

Tests with all four DIMM slots populated on the Gigabyte required a 2T Command Rate with 4 DIMMs in two dual channels. This is the pattern seen on other top-performing Socket 939 boards. There was no problem running 4 DS DIMMs at DDR400 at the same aggressive 2-2-2-7 settings, which worked well with 2 DIMMs.

Originally published at https://www.anandtech.com/show/1626 (Wayback Machine).