Archive 1997–2024

Socket 754 Roundup, Part 3: Asus, Soltek & DFI


DFI LANParty UT nF3 250Gb: Overclocking and Stress Testing

FSB Overclocking Results


Front Side Bus Overclocking Testbed
Default Voltage
Processor: Athlon 64 3200+
2.0GHz
CPU Voltage: 1.5V (default)
Cooling: Thermaltake Silent Boost K8 Heatsink/Fan
Power Supply: OCZ Power Stream 520W
Memory: OCZ PC3200 EL Platinum Rev. 2
or Geil PC3200 Ultra X
Maximum OC:
(Standard Ratio)
248 x 10
2470MHz (+24%)
Maximum FSB:
(Lower Ratio)
316 x 8 -1:1 Memory, 1 DIMM
270 x 9 at (1:1 Memory, 2 DIMMs)

The DFI LANParty UT nF3 250Gb was recently reviewed in-depth (DFI LANParty UT nF3-250Gb: Overclocker's Dream). Overclocking and Memory Performance charts are included here for easier reference. You should refer to the DFI review for complete information on the board's performance.

Memory Stress Test Results:


Stable DDR400 Timings - 1 DIMMs
(1/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 1.5
RAS to CAS Delay: 2T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 1T
*Several memory tests have shown that memory performs fastest on the nVidia nForce chipsets at a TRas (RAS Precharge) settings in the 9 to 13 range. We ran our own Memory Bandwidth tests with memtest86 with TRas settings from 5 to 15 at a wide range of different memory speeds. The best bandwidth was consistently at 9 to 11 at every speed, with TRas 10 always in the best range at every speed. The performance improvement at TRas 10 was only 2% to 4% over TRas 5 and 6 depending on the speed, but the performance advantage was consistent across all tests. All benchmarks were run at a TRas setting of 10.

We have not tested a Socket 754 board that offered a CAS 1.5 setting. The OCZ memory ran without problems with 1 DIMM at 1.5-2-2-10 settings.

Stable DDR400 Timings - 2 DIMMs
(2/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 1T

All earlier 754 benchmarks were run with 2 DIMMs, and this is the configuration that was used for all standard benchmark tests. The DFI LANParty UL was completely stable with 2 DIMMs at the rated timings of 2-2-2-10, at default speed.

Filling all three available memory slots is more strenuous on the memory sub-system than testing 2 DIMMs on a motherboard. We were very pleased to find that 3 DS DIMMs (1.5GB) of memory worked fine at timings almost the same as the aggressive timings which we used for 2 DIMMs. The DFI is one of the few Socket 754 boards that we have tested which can handle 3 DS DIMMs. You do need to use slightly slower timings with 3 DIMMs, but the 2-2-3-10 is very close to the rated 2-2-2-10 timings of the memory that we used for testing.

Stable DDR400 Timings - 3 DIMMs
(3/3 DIMMs populated - Single-Channel mode)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 3T
RAS Precharge: 10T*
Precharge Delay: 2T
Command Rate: 2T

The boot screen and Sisoft Sandra 2004 both reported a Command Rate of 2T when all 3 DIMM slots were filled.

Originally published at https://www.anandtech.com/show/1474 (Wayback Machine).