Archive 1997–2024

GPU Cheatsheet - A History of Modern Consumer Graphics Processors

Estimating Die Size

Disclaimer: Although we have close and ready contact with ATI and NVIDIA, the fact remains that some of the more technical issues concerning actual architecture and design are either closely guarded or extremely obscured to the public. Thus we attempt to estimate some die sizes and transistor counts based on information we already know - and some of these estimations are slightly incorrect.

One of the pieces of information a lot of people might like to know is the die size of the various graphics chips. Unfortunately, ATI and NVIDIA are pretty tight-lipped about such information. Sure, you could rip the heatsink off of your graphics card and get a relatively good estimate of the die size, but unless you've got some serious cash flow, this probably isn't the best idea. Of course, some people have done that for at least a few chips, which will be somewhat useful later. Without resorting to empirical methods of measuring, though, how do we estimate the size of a processor?

Before getting into the estimating portions, let's talk about how microprocessors are made, as it is rather important. When a chip is built up, it starts as a simple ingot of silicon cut into wafers on which silicon dioxide is grown. This silicon dioxide is cut away using photolithography in order to expose the silicon in certain parts. Next, polysilicon is laid down and etched, and the exposed silicon is doped (ionized). Finally, another mask is added with smaller connections to the doped areas and the polysilicon, resulting in a layer of transistors, with three contacts for each newly created transistor. After the transistors are built up, metal layers are added to connect them in the fashion required for the chip. These metal layers are not actually transistors but are connections between transistors that form the "logic" of the chip. They are a miniaturized version of the metal wires you can see in a motherboard.

Microprocessors will of course require multiple layers, but the transistors are on the one polysilicon layer. Modern chips typically have between 15 and 20 layers, although we really only talk about the metal layers. In between each set of metal layers is a layer of insulation, so we usually end up with 6 to 9 metal layers. On modern AMD processors, there are 8 metal layers and the polysilicon layer. On Intel processors, there are 6 to 8 metal layers plus the polysilicon layer, depending on the processor: i.e. 6 for Northwood, 7 on Prescott and 8 on most of their server/workstation chips like the Gallatin.

Having more layers isn't necessarily good or bad; it's simply a necessary element. More complex designs require more complex routing, and since two crossing wires cannot touch each, they need to run on separate layers. Potentially, having more metal layers can help to simplify the layout of the transistors and pack them closer together, but it also adds to the cost as there are now more steps in the production, and more layers results in more internal heat. There are trade offs that can be made in many areas of chip production. In AMD's case, where they only have 200 mm wafers compared to the 300 mm wafers that Intel currently uses, adding extra layers in order to shrink the die size and/or increase speeds would probably be a good idea.

Other factors also come into play, however. Certain structures can be packed more densely than others. For example, the standard SRAM cell used in caches consists of six transistors and is one of the smaller structures in use on processors. This means that adding a lot of cache to a chip won't increase the size as quickly as adding other types chip logic. The materials used in the various layers of a chip can also affect the speed at which the chip can run as well as the density of the transistors and routing in the other metal layers. Copper interconnects conduct electricity better than aluminum, for instance, and the Silicon On Insulator (SOI) technology pioneered by IBM can also have an impact on speed and chip size. Many companies are also using low-k dielectric materials, which can help gates to switch faster. All of these technologies add to the cost of the chip, however, so it is not necessarily true that a chip which uses, i.e. low-k dielectric, will be faster and cheaper to produce than a chip without it.

What all this means is that there is no specific way to arrive at an accurate estimate of die size without having in-depth knowledge of the manufacturing technologies, design goals, costs, etc. Such information is usually a closely guarded secret for obvious reasons. You don't want to let your competitors know about your plans and capabilities any sooner than necessary. Anyway, we now have enough background information to move on to estimating die sizes.

If we're talking about 130 nm process technology, how many transistors of that thickness would fit in 1 mm? Easy enough to figure out: 1 mm / .00013 mm = 7692 T/mm (note that .00013 mm = 130 nm). If we're working in two dimensions, we square that value: 59166864 T/mm2 ("transistors" is abbreviated to "T"). This is assuming square or circular transistors, which isn't necessarily the case, but it is close enough. So, does anyone actually think that they can pack transistors that tightly? No? Good, because right now that's a solid sheet of metal. If 59 million T/ mm2 is the maximum, what is a realistic value? To find that out, we need to look at some actual processors.

The current Northwood core has 55 million transistors and is 131 mm2. That equals 419847 T/mm2, assuming uniform distribution. That sounds reasonable, but how does it compare with the theoretical packing of transistors? It's off by a factor of 141! Again, assuming uniform distribution of materials, it means that 11.9 times (the square root of 141) as much empty space is present in each direction as the actual metal of the transistors. Basically, electromagnetic interference (EMI) and other factors force chip designers to keep transistors and traces a certain distance apart. In the case of the P4, that distance is roughly 11.9 times the process technology in both width and depth. (We ignore height, as the insulation layers are several times thicker than this). So, we'll call this value of 11.9 on the Northwood the "Insulation Factor" or "IF" of the design.

We now have a number we can use to derive die size, given transistor counts and process technology:

Originally published at https://www.anandtech.com/show/1463 (Wayback Machine).