Archive 1997–2024

Intel 925X Roundup: Creative Engineering 101


Abit AA8: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Processor: Pentium 4 Prescott LGA 775
2.8GHz
CPU Voltage: 1.3875V (default)
Cooling: Thermaltake Jungle 502
Power Supply: HiPro 470W
Maximum OC: 260FSB (+30%)

Like the earlier Socket 478 Pentium 4 processors, the LGA 775 CPUs are multiplier locked. Therefore, the only way to overclock the CPU is to increase the FSB. Unfortunately, the PCI Express bus is not locked, or rather, fixing the frequency tends to limit the overclocking of the 925X. Abit manipulates the PCIe frequency with µGuru during boot to achieve higher overclocks. For more information on how Abit manages to overclock the AA8, please check Breaking Intel's Overclock Lock: The REAL Story.

The AA8 was able to achieve a reach for FSB of 260, a 30% overclock, with an ATI X800 XT and SATA hard drive. Abit was able to achieve close to the same overclock with the nVidia 6800 Ultra at 258. The nVidia is generally less tolerant of out-of-spec PCIe frequency, so this performance is really excellent.

Memory Stress Test Results:

The memory stress test measures the ability of the Abit AA8 to operate at its officially supported memory frequency (533MHz DDR2), at the best performing memory timings that Crucial/Micron PC2-4300U will support. Memory stress testing was conducted by running DDR2 at 533MHz (stock 3:4 ratio) with 2 DIMM slots operating in Dual-Channel mode.

Stable DDR533 Timings - 2 DIMMs
(2/4 DIMMs - 1 Dual-Channel Bank)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 3.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10*
Command Rate: N/A
*SPD (Auto) timings for DDR2 are normally 4-4-4-12 at DDR2-533. A tRAS setting of 12 is normal. We ran a series of tests to measure memory bandwidth, and found the tRAS setting made very little difference in the performance of DDR2. The most effective range of tRAS was 8 to 13 for DDR2 on the 925X chipset, so a tRAS of 10 was chosen for benchmarking.

The Abit AA8 DuraMAX was completely stable with 2 DIMMs in Dual-Channel at the DDR2 settings of 3-3-3-10 at 1.8V default voltage. These are much faster settings than the DDR2 SPD and rated timings of 4-4-4-12.

Filling all four available memory slots is more strenuous on the memory sub-system than testing 2 DDR2 modules on a motherboard.

Stable DDR533 Timings - 4 DIMMs
(4/4 DIMMs - 2 Dual-Channel Banks)
Clock Speed: 266MHz
Timing Mode: 3:4 (200:266 - Default)
CAS Latency: 4.0
Bank Interleave: Auto
RAS to CAS Delay: 3
RAS Precharge: 3
Cycle Time (tRAS): 10
Command Rate: N/A

DDR has a long benchmarking history that makes it easier to figure out where to go with memory timings. We are still in the learning curve with DDR2, and the old DDR patterns just do not work in DDR2. We found that no matter what the rest of the settings, 4 DIMMs with DDR2 required CAS 4 for stability. Timings like 3-4-3 or 3-4-4 appeared to work fine, and then we were suddenly facing hard drive corruption. Our advice for now is to use CAS 4 with 4 DIMMs for stability, although 4-3-3 timings did work fine on many of the test boards. If you plan to try raising voltage to attempt lower CAS with 4 DIMMs, then please backup your system first. Our test beds gave no warning at all before hard drive corruption with overly aggressive timings using 4 DIMMs.

Originally published at https://www.anandtech.com/show/1431 (Wayback Machine).