Socket 754 Roundup: Comparing Generation 2
- Posted in
- Motherboards
Gigabyte K8NSNXP: Overclocking and Stress Testing
FSB Overclocking Results
| Front Side Bus Overclocking Testbed | |
| Default Voltage | |
| Processor: | Athlon 64 3200+ 2.0GHz |
| CPU Voltage: | 1.5V (default) |
| Cooling: | AMD Stock Athlon 64 Heatsink/Fan |
| Power Supply: | Antec TruePower 430W |
| Maximum OC: (Standard Ratio) |
242FSB x10 2420MHz (+21%) (246 with EZTune4) |
| Maximum FSB: (Lower Ratio) |
242FSB x 10 at 1:1 Memory (275x8.5 at 1:1 with EZTune4) |
On paper, the Gigabyte K8NSNXP should be an incredible performer, but we found that no matter what we did, the Gigabyte would not boot at any ratio, at a speed higher than a BIOS setting of 242. This seems to be an artificial boot limiter, since we were able to reach a very competitive 275x8.5 using EZTune4 in Windows XP. While we were happy to see this level of performance with EZTune4, it is still a much less convenient method of overclocking than tuning the same settings in BIOS. EZTune4 does allow settings to be saved, so Windows will load at the same overclock on reboot, but we really wish that Gigabyte would give us a choice on how we wish to overclock. Gigabyte has been using what appears to be BIOS boot limits on several recent boards, probably to limit the number of boards destroyed by indiscriminate overclock settings in BIOS. We do understand why, but we still prefer to dial our own, as do most other overclockers.
The other complaint with recent Gigabyte boards is the extremely limited range of memory voltage adjustments that are provided. Memory is now available that is warranted to 3.0V to 3.2V, and an adjustment of just +0.2V for vDIMM is just not enough for some memory. The Chipset and HT voltage adjustments partially offset this limitation, but they are not an adequate substitute for such a limited selection of vDIMM settings. Gigabyte builds very reliable motherboards, and with a little more attention to memory voltage and BIOS overclocking, they would consistently be at or near the top in every roundup.
Memory Stress Test Results:
The memory stress test simply checks the ability of the Gigabyte K8NSNXP to operate at its officially supported memory frequency (400MHz DDR), at the best performing memory timings that our Mushkin PC3500 Level 2 or OCZ PC3500 Platinum Ltd Modules will support. Memory stress testing was conducted by running RAM at 400MHz with 2 DIMM slots filled.| Stable DDR400 Timings - 2 DIMMs (2/3 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| Timing Mode: | N/A |
| CAS Latency: | 2.0 |
| Bank Interleave: | N/A |
| RAS to CAS Delay: | 2T |
| RAS Precharge: | 10T (10T for Best Performance)* |
| Precharge Delay: | 2T |
| Command Rate: | N/A |
*Several memory tests have shown that memory performs fastest on the nVidia nForce and VIA K8T800 chipsets at a TRas (RAS Precharge) setting in the 9 to 13 range. We ran our own Memory Bandwidth tests with memtest86 with TRas settings from 5 to 15 at a wide range of different memory speeds. The best bandwidth was consistently at 9 to 11 at every speed, with TRas 10 always in the best range at every speed. The memory bandwidth improvement at TRas 10 was only 2% to 4% over TRas 5 and 6 depending on the speed, but the performance advantage was consistent across all tests. Since best performance was achieved at 2-2-2-10 timings, all Athlon 64 benchmarks were run at a TRas setting of 10.
The Gigabyte K8NSNXP was completely stable with 2 DIMMs at the best performing settings of 2-2-2-10 at default speed, but we did need to boost memory voltage slightly by +0.1V for best stability. Higher overclocks could be achieved with 1 DIMM compared to 2 DIMMs, but at default speed, 1 or 2 DIMMs were reliable at the same aggressive 2-2-2-10 timings.
Filling all three available memory slots is more strenuous on the memory subsystem than testing 2 DIMMs on a motherboard. As we found on most other nF3-250 boards, 3 DS DIMMs (1.5GB) of memory worked fine at timings almost the same as the aggressive timings that we used for 2 DIMMs.
| Stable DDR400 Timings - 3 DIMMs (3/3 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| Timing Mode: | N/A |
| CAS Latency: | 2.0 |
| Bank Interleave: | N/A |
| RAS to CAS Delay: | 3T |
| RAS Precharge: | 10T |
| Precharge Delay: | 2T |
| Command Rate: | N/A |
Three DIMMs required 2-2-3-10 timings for stable operation, but they remained stable at the +0.1V memory voltage that was required with 2 DS DIMMs. 2-2-3 is very close to the best performing 2-2-2-10 timings with 2 dimms.
Originally published at https://www.anandtech.com/show/1333 (Wayback Machine).