Archive 1997–2024

Socket 754 Roundup: Comparing Generation 2


Abit KV8 PRO: Overclocking and Stress Testing

FSB Overclocking Results


Front Side Bus Overclocking Testbed
Default Voltage
Processor: Athlon 64 3200+
2.0GHz
CPU Voltage: 1.5V (default)
Cooling: AMD Stock Athlon 64 Heatsink/Fan
Power Supply: Antec TruePower 430W
Maximum OC:
(Standard Ratio)
248FSB x10
2480MHz (+24%)
Maximum FSB:
(Lower Ratio)
No Ratios Available

This late 3200+ achieved about the same outstanding overclock on the Abit K8V PRO that we saw in our review of the K8N Neo Platinum. The Abit reached 248FSB at the stock 10X multiplier and default voltage. However, to even test the stock 10X multiplier, we had to force the Abit to 10X with the free Clock Generator utility from www.cpuid.com. This 24% overclock at stock multiplier suggests that our late 3200+ is coming from improved yields on the AMD production line for Athlon 64. If this is really the case, it is very good news for overclocking enthusiasts.

We were not able to test the highest FSB that could be achieved by lowering the multiplier, since no ratio adjustments were available on the Abit. Multipliers on Athlon 64 chips are unlocked at ratios below the shipping multiplier. This is primarily a result of the Cool'n'Quiet feature according to AMD, and AMD refers to this as Athlon 64 processors being "downclockable". FX chips are completely unlocked, and can be set at either higher or lower ratios than stock. Abit tells us that they will add ratios to a future BIOS, and they are working on a BIOS revision to correct the problem with the incorrect boot ratio. By using Clock Gen, we were able to verify that the KV8 PRO could reach 275 1:1 at an 8X multiplier with a DDR550 DIMM.

Memory Stress Test Results:

The memory stress test is very basic, as it tests the ability of the Abit KV8 PRO to operate at its officially supported memory frequency (400MHz DDR), at the best performing memory timings that our Mushkin PC3500 Level 2 or OCZ PC3500 Platinum Ltd Modules will support. Memory stress testing was conducted by running RAM at 400MHz with 2 DIMM slots filled. However, please keep in mind that Socket 754 is single-channel and will still operate at top speed with just one DIMM.

Stable DDR400 Timings - 2 DIMMs
(2/2 DIMMs populated)
Clock Speed: 200MHz
Timing Mode: N/A
CAS Latency: 2.0
Bank Interleave: N/A
RAS to CAS Delay: 2T
RAS Precharge: 10T
(10T for Best Performance)*
Precharge Delay: 2T
Command Rate: 1T

*Several memory tests have shown that memory performs fastest on the nVidia nForce and VIA K8T800 chipsets at a TRas (RAS Precharge) setting in the 9 to 13 range. We ran our own Memory Bandwidth tests with memtest86 with TRas settings from 5 to 15 at a wide range of different memory speeds. The best bandwidth was consistently at 9 to 11 at every speed, with TRas 10 always in the best range at every speed. The memory bandwidth improvement at TRas 10 was only 2% to 4% over TRas 5 and 6 depending on the speed, but the performance advantage was consistent across all tests. Since best performance was achieved at 2-2-2-10 timings, all Athlon 64 benchmarks were run at a TRas setting of 10.

The Abit KV8 PRO was completely stable with 2 DIMMs at the best performing settings of 2-2-2-10 at default speed. Higher overclocks could be achieved with 1 DIMM compared to 2 DIMMs, but at default speed, 1 or 2 DIMMs were reliable at the same aggressive 2-2-2-10 timings.

Abit had no adjustments at all for Bank Interleave or Command Rate, but the Command Rate is likely set to 1T. We have been discovering that Command Rate is very important to performance of Athlon 64 Dual channel memory and it should be set to 1T if possible for best performance.

Originally published at https://www.anandtech.com/show/1333 (Wayback Machine).