Archive 1997–2024

Opus Technologies' Titanium MT-200 Mid-tower Chassis


Benchmarking

When benchmarking the MT-200, we test the temperatures of key components including the actual CPU temperature, the actual temperature inside the heatsink, the temperatures of the DDR, Northbridge, Southbridge, HDD, PSU, and the ambient temperature inside the case, all during normal operation. During our testing, the PSU and CPU heatsink fans remain on to measure temperatures during normal system operations.

Gigabyte GA-7VRX
AMD Athlon MP 2100+
2 x 128 DDR Corsair XMS 2400
ThermalTake Volcano 7
Seagate Cheetah 10000RPM
Inno3D GeForce4 Ti 4200
TTGI 4 Fan 520W


Thermometer Positions


The thermal readings for the key components and points on the motherboard during operation were as follows:

Opus Technologies, Inc. MT-200
 System On-Time  CPU  Heatsink  HDD  DDR  Northbridge  Southbridge  Power Supply  System Ambient
10 52.5 37.5 28.8 34.3 39.1 39.3 29.3 29.7
30 53.7 39.0 29.5 36.8 40.2 39.9 31.2 30.4

NZXT Guardian
 System On-Time  CPU  Heatsink  HDD  DDR  Northbridge  Southbridge  Power Supply  System Ambient
10 53.4 36.7 30.5 37.1 40.2 39.9 29.8 31.9
30 55.3 37.5 33.2 38.5 41.8 41.2 31.9 35.1

Ahanix Black Knight X195
 System On-Time  CPU  Heatsink  HDD  DDR  Northbridge  Southbridge  Power Supply  System Ambient
10 51.9 35.3 25.3 35.1 38.4 39.1 29.2 28.2
30 52.5 36.2 26.1 38.4 40.0 39.9 30.8 29.6

Since the MT-200 did not come with any case fans, we decided it would be best to install third party fans to simulate a typical system. We installed four 80mm fans, just as many as the Thermaltake VM3000 Skull series had. Though an optional 120mm fan can be mounted at the front of the chassis as an intake, we thought it would be best to test the case in the same state that the VM3000 was tested, since they are basically the same chassis.

In our heat tests, we predicted the results for the MT-200 to be close to, if not the same as, the VM3000. There was only a slight variability in the temperature readings, since there is always room for error. The MT-200 did, however, perform better than the NZXT Guardian, most likely due to the number of fans. A fifth, 120mm fan can also be mounted at the front to increase air flow, thus reducing temperatures further.

Since the Thermaltake Xaser VM3000 Skull produced about 55dBA of noise, we predicted the MT-200 to have the same noise levels. We measured the noise level of the MT-200 12" away from the closed chassis with the power supply fan turned off. Take a look at our results.

 Case  dBA
Opus Technologies MT-200 56
NZXT Guardian 49
Ahanix Black Knight X195 50
Lian Li PC-6070 44
Thermaltake Xaser III VM3000A - Skull 55

We read the noise levels of the MT-200 at about 1dBA higher than the VM3000. Lian Li's PC-6070 had sound-dampening foam, which lined the inside of its front bezel, and side and top panels to reduce noise levels about 10dBA. We hope all other case manufactures consider this in future designs, since it is a very effective method in reducing noise.

Originally published at https://www.anandtech.com/show/1305 (Wayback Machine).