Archive 1997–2024

Intel's E7205: Granite Bay Hits the Streets

Tyan S2662: Stress Testing

The S2662 had some pretty decent stress testing potential, mostly because it's based on a dual channel chipset (E7205), which is a more complex and difficult chipset to implement (due to signal integrity, among other issues) than the conventional single channel DDR chipsets that dominate today's markets. However, since this BIOS allowed no overclocking whatsoever, our stress tests only consist of memory testing. Here's what we managed to include:

  1. Memory stress testing was conducted by running RAM at 266MHz with two banks full and at 266MHz with four banks full at the most aggressive timings possible.

Memory Stress Test Results:

Running two modules of Corsair XMS memory at dual DDR266 should be very easy for the Tyan S2662. Indeed, it was quite easy, although we were of course unable to adjust any timings since the S2662 BIOS contained no such adjustments:

Stable Dual DDR266 Timings
(2/4 banks populated)

Clock Speed:
133MHz
Timing Mode:
N/A
CAS Latency:
N/A
Bank Interleave:
N/A
Precharge to Active:
N/A
Active to Precharge:
N/A
Active to CMD:
N/A
Command Rate:
N/A

Pretty good timings, eh? No, there obviously aren't any timings we can analyze here, but if you skip a few pages to our stock benchmark testing, you'll see that the Tyan S2662 is able to compete admirably with ASUS and Gigabyte's E7205 solutions, which have been tweaked to the max for performance. At dual DDR266, the S2662 was quite stable, as it was able to complete our entire benchmark suite, which includes Sysmark 2002, Quake3 Arena, Jedi Knight II, Unreal Tournament 2003, SPECviewperf 7.0, Sciencemark, and XMPEG. Prime95 ran for only a few hours, since we were strapped for time in getting this review out the door. Still, all in all, our results give a pretty decent indication that the S2662 can handle dual DDR266, and everyone should expect it to.

In this next scenario we test how well the Tyan S2662 can handle a full load of memory modules:

Stable Dual DDR266 Timings
(4/4 banks populated)

Clock Speed:
133MHz
Timing Mode:
N/A
CAS Latency:
N/A
Bank Interleave:
N/A
Precharge to Active:
N/A
Active to Precharge:
N/A
Active to CMD:
N/A
Command Rate:
N/A

Everything ran smoothly with four DIMMs populated running at 266MHz. We were able to complete a few hours of Prime95 torture testing as well as other general apps.

We should remind you that all the E7205 motherboards we've tested here today (S2662 included) can only operate a certain amount of modules in a specific way. You can always operate this board with one module or with two modules installed, that's not surprising. However, if you want to add a third module to memory bank 3 or 4, you won't be so lucky. E7205 motherboards will simply disable the third module, and operate with just the two modules in banks 1 and 2. Clearly though, you'll be able to operate four DIMMs successfully, so there's nothing to worry about there.

Another issue we wanted to explore was how well Granite Bay would be able to run multiple types of memory modules. Therefore, we tested the most stressful situation possible and installed 4 DIMMs into the S2662. One scenario included four Corsair XMS modules installed, and the other dealt with two Corsair XMS modules (Winbond chips) and two Mushkin modules (Winbond chips). We successfully booted into Windows and played around for a while in both scenarios. All of our usual activities (like running XMPEG movies, data compression, DX8 games, etc.) worked perfectly fine in both situations. It seems as if you'll be able to operate different types of memory modules with the S2662, although we would have to do much more testing to be sure.

Originally published at https://www.anandtech.com/show/1033 (Wayback Machine).